evantagecontrols.co.uk Report : Visit Site

Technical data of the evantagecontrols.co.uk

Geo IP provides you such as latitude, longitude and ISP (Internet Service Provider) etc. informations. Our GeoIP service found where is host evantagecontrols.co.uk. Currently, hosted in United Kingdom and its service provider is UK Web .

HTTP Header Analysis

HTTP Header information is a part of HTTP protocol that a user's browser sends to called Apache containing the details of what the browser wants and will accept back from the web server.

DNS

HtmlToText

pir occupancy switches for commercial and domestic use the e-vantage flush mounted pir switch is suitable for easy mounting through a 73/75mm diameter hole into a ceiling void which is at least 78mm deep. configurable for any room occupancy style, via time and lux level adjusters. it switches on the lighting load if the area is occupied and if the ambient lux level is less than the chosen adjusted level (10 to 1000 lux). it switches off the lighting load if the area is unoccupied for the set time (up to 40 minutes). it is also suitable for non-lighting loads by setting the lux adjuster to the maximum point. technical details voltage: 220 - 240vac, 50hz loading: 1000w of resistive loads 750w of fluorescent loads 750w of transformer loads 750w of cfl, led and 2d lamps minimum load: 2w resistive, suitable for most energy saving lamps, leds and emergency fittings ip rating: ip20 detection range: 360 degrees with 5m diameter when mounted at a 2.4m ceiling height time: 10 seconds to 40 minutes in 9 steps lux: 10 to 1000 lux and maximum (photocell inactive) at the pir switch installation to be installed by a competent person with reference to bs 7671. make reference to the technical details (above) and precautions (below). if in doubt consult a qualified electrician. plan where the pir is to be located (see diagram 1). switch off supply and check for hidden cables and pipes. make a 73/75mm diameter hole through a standard ceiling board. ensure both springs are fitted to the moulding in the correct orientation (see diagram 2) suggested typical wiring (also refer to diagram 3). lay a triple (brown, black, grey) and earth cable between the hole and the light fitting. connection at the light fitting: - remove all of the live cores from the light fitting and connect t o the brown core. - sleeve the grey core with brown sleeving and connect to the l ive terminal of the light fitting. - sleeve the black core with blue sleeving and add to the n eutral terminal of the light fitting. - sleeve the earth core with green and yellow sleeving and c onnect to the earth terminal of the light fitting. connection at the pir: - connect the brown core to the pir’s live terminal (l). - sleeve the grey core with brown sleeving and connect to the p ir’s switched line terminal (sl). - sleeve the black core with blue sleeving and connect to the p ir’s neutral terminal (n). - the pir is double insulated (no earth needed) cut back or m ake safe the earth core. - fix the pir terminal cover with the two screws provided. push the pir into the ceiling void, making reference to diagram 4. ensure the time adjuster is set to minimum and lux to photocell inactive (maximum), making reference to diagram 5. turn on the supply and any in-line switch and check the operation of the pir. operation when the power is switched on, the pir will switch on the lighting load for 1 minute then switch it off. after 2 seconds it will switch on again if it detects movement. with time set to minimum the load will stay on for 10 seconds so the detection range can be easily assessed. lux set up note: for loads which should turn on regardless of ambient light levels, set lux to maximum (photocell inactive). it is best to set lux when the ambient light level is at the required minimum level. set lux to the minimum and wait for the load to switch off. keeping to the side of the pir, slowly increase lux whilst waving your hand below the pir until the lighting load switches on. time set up with time set to maximum (40 minutes) it halves at each point as moved towards minimum i.e. from max to min: 40 mins, 20 mins, 10 mins, 5 mins, 2.5 mins, 80 secs, 40 secs, 20 secs, 10 secs. the time adjuster should be set appropriately for the usage of the area, for example some possible settings could be: offices with workers regularly walking 20 minutes offices with mainly desk based workers 40 minutes corridors 5 minutes washrooms with total coverage 10 minutes washrooms with entry coverage only 40 minutes 2d fittings* 20 minutes (minimum) * not less than 20 minutes due to potential lamp failure. if in doubt contact your lamp manufacturer. precautions do not place the pir near heat sources, fans or in ventilated ceiling voids. these pirs can be wired in parallel (sharing the same live, switch line and neutral) however: - some lamps emit infra red radiation, if these are nearby and s witched via another pir switch the pir may false trigger. do not place close to, or positioned such that, any light source points directly into the pir. ensure wires and cables are securely held within the connection terminals. do not connect on a circuit with large inductive loads, as induced spikes may cause false triggering or damage the pir. the pir should be protected by a 5 or 6 ampere mcb or fuse. disconnect the pir from the circuit before performing insulation testing of the wiring circuit 3 year warranty ev pirfl comes with a 3 year warranty from the date of manufacture and is ce marked. if you experience problems please return the pir to your supplier with details of the fault, load and application. company registered number 2570169

URL analysis for evantagecontrols.co.uk

Whois Information

Whois is a protocol that is access to registering information. You can reach when the website was registered, when it will be expire, what is contact details of the site with the following informations. In a nutshell, it includes these informations;

Error for "evantagecontrols.co.uk".

the WHOIS query quota for 2600:3c03:0000:0000:f03c:91ff:feae:779d has been exceeded
and will be replenished in 420 seconds

WHOIS lookup made at 04:45:27 16-Jul-2017

--
This WHOIS information is provided for free by Nominet UK the central registry
for .uk domain names. This information and the .uk WHOIS are:

Copyright Nominet UK 1996 - 2017.

You may not access the .uk WHOIS or use any data from it except as permitted
by the terms of use available in full at http://www.nominet.uk/whoisterms,
which includes restrictions on: (A) use of the data for advertising, or its
repackaging, recompilation, redistribution or reuse (B) obscuring, removing
or hiding any or all of this notice and (C) exceeding query rate or volume
limits. The data is provided on an 'as-is' basis and may lag behind the
register. Access may be withdrawn or restricted at any time.

  REFERRER http://www.nominet.org.uk

  REGISTRAR Nominet UK

SERVERS

  SERVER co.uk.whois-servers.net

  ARGS evantagecontrols.co.uk

  PORT 43

  TYPE domain

DISCLAIMER
This WHOIS information is provided for free by Nominet UK the central registry
for .uk domain names. This information and the .uk WHOIS are:
Copyright Nominet UK 1996 - 2017.
You may not access the .uk WHOIS or use any data from it except as permitted
by the terms of use available in full at http://www.nominet.uk/whoisterms,
which includes restrictions on: (A) use of the data for advertising, or its
repackaging, recompilation, redistribution or reuse (B) obscuring, removing
or hiding any or all of this notice and (C) exceeding query rate or volume
limits. The data is provided on an 'as-is' basis and may lag behind the
register. Access may be withdrawn or restricted at any time.

  REGISTERED no

DOMAIN

  NAME evantagecontrols.co.uk

NSERVER

  NS2.VIDAHOST.COM 91.146.110.188

  NS1.VIDAHOST.COM 91.198.165.131

Mistakes

The following list shows you to spelling mistakes possible of the internet users for the website searched .